Huawei DDSU666-H (1-Ph)

Indirect measurement wattmeter (ampere clamp included)
It allows measuring the consumption of our electrical network.
With an RS485 communication interface to communicate with Huawei inverters
3 years warranty.

• 1 % high-accuracy power measurement for precise control of consumption, generation, and energy optimization
• Plug & play integration with Sigenergy systems via Modbus, no extra configuration needed
• Real-time monitoring with 100 ms data refresh for instantaneous response
• Versatile installation: direct connection up to 100 A or with external current transformers (CTs)

Sigen Power Sensor integrates seamlessly with Sigenergy devices, with no configuration required.
This power sensor is part of SigenStor's 5-in-1 energy storage system.
Sigenergy's ESS seamlessly integrates the PV inverter, battery power conversion system (PCS), EV DC charger for electric vehicles, battery pack and energy management system (EMS).

Sigen Power Sensor integrates seamlessly with Sigenergy devices, with no configuration required.
This power sensor is part of SigenStor's 5-in-1 energy storage system.
Sigenergy's ESS seamlessly integrates the PV inverter, battery power conversion system (PCS), EV DC charger for electric vehicles, battery pack and energy management system (EMS).

• 1 % high-accuracy power detection for precise control
• 100 A single-phase direct connection with built-in CT
• Modbus RTU communication via RS485
• Supports export/import limitations and AI-ready

• 1% high-accuracy power detection for precise control
• Integrates smoothly with Sigenergy devices, no need for setup
• Top-class 100 A direct connection in Power Sensor with built-in CT
• 100 ms data refresh rate, instantaneous data feed

A power meter transmits the measured amount of power to the SolarLog for analysis. It serves as a consumption meter, showing a comparison of produced and consumed power. It can be configured to operate with the SolarLog in three different modes:
- Measuring energy consumption for optimal utilization of the power generated.
- Measuring the total amount of energy that has been fed into the grid.
- Measuring the energy production of inverters that are not directly managed by SolarLog.

Three-phase bidirectional meter.
Nominal voltage 230 V/400 V
Frequency 50 Hz/±5 %.
Nominal/limit current per phase conductor 5 A/63 A (>63 A combined with external current transformers)
Starting current <25 mA
Connection cross-section From 10 mm² to 16 mm² 1) (for 63 A protection)

Măsurare indirectă.

Control center and energy manager via Ethernet, including Energy Meter.

Smart Meter TS 65A-3; for recording energy consumption, three-phase, direct metering

Modular electric energy meter that displays power (kWh, kVArh and kVA) and other measurements directly on its backlit LCD display.
It is designed for three-phase load metering with connection via CT and is suitable for applications up to 12000 A.

Energy meters are typically used in an energy storage system, to measure the power and energy of the entire application in the distribution box and minimize the import or export of energy to the grid. They can also be used to measure the output of a PV inverter or AC loads and display the data on GX devices such as the Cerbo GX or Ekrano GX and the VRM gateway.
ET340 (RS485 - for 3-phase max. 65 A)

The Victron EM24 Ethernet is a standard device for measuring the power and energy of a three-phase application, for example in the distribution box or for measuring the output of a PV inverter, an AC generator or an inverter or inverter/charger.

Solis-1P-Meter-CT*1

Indirect measurement single-phase wattmeter
Open-core toroids included with measurement capacity per phase of up to 150A and 5 meters of cable
LCD screen for real-time display of measurements
Includes 10m RS485 cable with connector for Solis inverters as standard
DIN35 rail mounting

Solis-3P-Meter-CT*3 (indirect measurement)

Preconfigured and ready to communicate with all three-phase Solis inverters
Indirect measurement wattmeter, installation without the need to modify the customer's installation
DIN35 rail mounting
LCD screen for real-time display of measurements
Open-core toroids included with measurement capacity per phase of up to 150A and 5 meters of cable
Includes 10m RS485 cable with connector for Solis inverters as standard
Ability to use other toroids with a 5 amp secondary simply by setting the transformation ratio

Solis-3P-Meter (Directo)

Direct measurement three-phase wattmeter
DIN35 rail mounting
It controls consumption and performs 0 discharge to the network, it also measures the energy exported to compensate for surpluses
LCD screen for real-time display of measurements
Communication with the inverter via RS485

Features:

Indirect measurement wattmeter, installation without the need to modify the customer's installation.
DIN35 rail mounting
LCD display for real time display of measurements
10m RS485 cable with Solis inverter connector included as standard.
Ability to use other toroidals with secondary at 5 amps simply by setting the transformation ratio

Solis-1P-Meter

Direct measurement single-phase wattmeter
Communication with the inverter via RS485
DIN rail 35
8-bit LCD display
Measuring range (A) : 10(60A)

Sigen Power Sensor integrates seamlessly with Sigenergy devices, with no configuration required.
This power sensor is part of SigenStor's 5-in-1 energy storage system.
Sigenergy's ESS seamlessly integrates the PV inverter, battery power conversion system (PCS), EV DC charger for electric vehicles, battery pack and energy management system (EMS).