Maximum voltage: 1500 V
Cable diameter: 5,5 - 9 mm
Cable cross section: 4 -6 mm2

Maximum voltage: 1500 V
Cable diameter: 5,5 - 9 mm
Cable cross section: 4 -6 mm2

Huawei DDSU666-H (1-Ph)

Indirect measurement wattmeter (ampere clamp included)
It allows measuring the consumption of our electrical network.
With an RS485 communication interface to communicate with Huawei inverters
3 years warranty.

• 1 % high-accuracy power measurement for precise control of consumption, generation, and energy optimization
• Plug & play integration with Sigenergy systems via Modbus, no extra configuration needed
• Real-time monitoring with 100 ms data refresh for instantaneous response
• Versatile installation: direct connection up to 100 A or with external current transformers (CTs)

Huawei Smart Power Sensor DTSU666-H (3-Ph).
Valid if cable section doesn't exceeds 95 mm2 and there's not a higher intensity of 250 A.

Sigen Power Sensor integrates seamlessly with Sigenergy devices, with no configuration required.
This power sensor is part of SigenStor's 5-in-1 energy storage system.
Sigenergy's ESS seamlessly integrates the PV inverter, battery power conversion system (PCS), EV DC charger for electric vehicles, battery pack and energy management system (EMS).

Sigen Power Sensor integrates seamlessly with Sigenergy devices, with no configuration required.
This power sensor is part of SigenStor's 5-in-1 energy storage system.
Sigenergy's ESS seamlessly integrates the PV inverter, battery power conversion system (PCS), EV DC charger for electric vehicles, battery pack and energy management system (EMS).

• 1 % high-accuracy power detection for precise control
• 100 A single-phase direct connection with built-in CT
• Modbus RTU communication via RS485
• Supports export/import limitations and AI-ready

Transformador ABRIBLE 150/5
Sección hasta 95 mm2

Power Meter, DTSU666-HW/YDS60-80
Direct reading up to 80A
Supports indirect reading with CT x/5A (not included)

Transformadores abribles de medida 1000/5

Modbus 3-phase current meter

Temperature range -40 ° C to + 90 ° C
Max. conductor temperature + 120 ° C (20,000 h)
Nominal voltage U0 / UAC1.0 / 1.0 kVDC 1.5 / 1.5 kV
Weather and UV resistance

Panou de protectie fotovoltaic pentru 2 intrari + 2 iesiri. 1000Vdc, 15A pe intrare, cu siguranță și bază pentru siguranță. Carcasă de 12 module din ABS. conectori MC4.

Transformadores abribles de medida 1500/5

Temperature range -40 ° C to + 90 ° C
Max. conductor temperature + 120 ° C (20,000 h)
Nominal voltage U0 / UAC1.0 / 1.0 kVDC 1.5 / 1.5 kV
Weather and UV resistance

A power meter transmits the measured amount of power to the SolarLog for analysis. It serves as a consumption meter, showing a comparison of produced and consumed power. It can be configured to operate with the SolarLog in three different modes:
- Measuring energy consumption for optimal utilization of the power generated.
- Measuring the total amount of energy that has been fed into the grid.
- Measuring the energy production of inverters that are not directly managed by SolarLog.

Three-phase bidirectional meter.
Nominal voltage 230 V/400 V
Frequency 50 Hz/±5 %.
Nominal/limit current per phase conductor 5 A/63 A (>63 A combined with external current transformers)
Starting current <25 mA
Connection cross-section From 10 mm² to 16 mm² 1) (for 63 A protection)