Solis-1P-Meter

Direct measurement single-phase wattmeter
Communication with the inverter via RS485
DIN rail 35
8-bit LCD display
Measuring range (A) : 10(60A)

Temperature range - 40 °C to + 90 °C (for fixed and flexibleinstallation)
Max. Temperature at conductor + 120°C (20.000 h, 50 % residual elongation)
Rated voltage U0/U AC 1,0 / 1,0 kV DC 1,5 / 1,5 kV
Resistance weather-resistant and UV-resistance

Temperature range -40 ° C to + 90 ° C
Max. conductor temperature + 120 ° C (20,000 h)
Nominal voltage U0 / UAC1.0 / 1.0 kVDC 1.5 / 1.5 kV
Weather and UV resistance

Temperature range -40 ° C to + 90 ° C
Max. conductor temperature + 120 ° C (20,000 h)
Nominal voltage U0 / UAC1.0 / 1.0 kVDC 1.5 / 1.5 kV
Weather and UV resistance

Sigen Power Sensor Single Phase DH

Sigen Power Sensor Single Phase DH

Sigen Power Sensor Trifásico

Three-phase Sigen Power Sensor CT600-DH
Sigen Power Sensor integrates seamlessly with Sigenergy devices, with no configuration required.
This power sensor is part of SigenStor's 5-in-1 energy storage system.
Sigenergy's ESS seamlessly integrates the PV inverter, battery power conversion system (PCS), EV DC charger for electric vehicles, battery pack and energy management system (EMS).

Control center and energy manager via Ethernet, including Energy Meter.

Cuadro de protección fotovoltaico para 2 entradas + 2 salidas. 1000Vcc, 15A por entrada, con fusible y base de fusible. Envolvente de 12 módulos en ABS. Conectores MC4.

Smart Meter TS 65A-3; for recording energy consumption, three-phase, direct metering

Fronius Smart Meter TS 5KA Three Phase is a calibrated device to measure and control the amount of energy passing through the house.
It requires toroidal sensors to carry out an indirect measurement of the current passing through each of the 3 phases.

Single-phase smart meter for direct connection up to 100 A

A power meter transmits the measured amount of power to the SolarLog for analysis. It serves as a consumption meter, showing a comparison of produced and consumed power. It can be configured to operate with the SolarLog in three different modes:
- Measuring energy consumption for optimal utilization of the power generated.
- Measuring the total amount of energy that has been fed into the grid.
- Measuring the energy production of inverters that are not directly managed by SolarLog.

Convertidor de corriente
Set formado por un transductor de medida 1 A y una bobina Rogowski con línea de señales. Longitud de la bobina Rogowski: 600 mm, diámetro: 190 mm. Longitud de la línea de señales: 10 m. La bobina Rogowski mide corriente AC de barras colectoras y líneas de alta tensión

Maximum voltage: 1500 V
Cable diameter: 5,5 - 9 mm
Cable cross section: 4 -6 mm2

Power Meter, DTSU666-HW/YDS60-80
Direct reading up to 80A
Supports indirect reading with CT x/5A (not included)

Huawei Smart Power Sensor DTSU666-H (3-Ph).
Valid if cable section doesn't exceeds 95 mm2 and there's not a higher intensity of 250 A.

Huawei DDSU666-H (1-Ph)

Indirect measurement wattmeter (ampere clamp included)
It allows measuring the consumption of our electrical network.
With an RS485 communication interface to communicate with Huawei inverters
3 years warranty.